1分快3平台

<video id="hx5p7"><noframes id="hx5p7"><pre id="hx5p7"></pre>
<thead id="hx5p7"><dfn id="hx5p7"><output id="hx5p7"></output></dfn></thead>

<form id="hx5p7"><listing id="hx5p7"></listing></form>
    <thead id="hx5p7"><var id="hx5p7"><output id="hx5p7"></output></var></thead>

    <address id="hx5p7"><listing id="hx5p7"><ins id="hx5p7"></ins></listing></address>
    <address id="hx5p7"><dfn id="hx5p7"></dfn></address>

      <address id="hx5p7"></address>

        <sub id="hx5p7"><var id="hx5p7"><ins id="hx5p7"></ins></var></sub>
        <address id="hx5p7"><var id="hx5p7"></var></address><address id="hx5p7"></address>

        <sub id="hx5p7"><dfn id="hx5p7"><output id="hx5p7"></output></dfn></sub>

        <sub id="hx5p7"></sub>

        <sub id="hx5p7"><listing id="hx5p7"><ins id="hx5p7"></ins></listing></sub>

            <address id="hx5p7"></address>
          <sub id="hx5p7"></sub>

          News新闻动态

          新闻动态
          钣金加工的检验标准与操作要点

          钣金加工的检验标准与操作要点,主要包括:

          1、应对图纸进行检查,以便检查折弯等操作工序的方向是否正确,是否有错误,还有就是资料、板厚等是否正确,以及尺寸是否能够得到保证等。

          2、如果要进行电镀的话,则是要求工件等的表面应处理干净才行,而且不能有缺陷问题。如有,则应及时进行处理和解决。

          3、如果工件有质量问题,或是表面有缺陷的话,那么应检查其是否能够进行处理和解决,是否会影响到后面的加工等。如对加工有影响的话,那么则不能进行加工操作。

          4、成品加工完毕后,应进行必要的检验与检查,是否存在问题等。

          1分快3平台

          <video id="hx5p7"><noframes id="hx5p7"><pre id="hx5p7"></pre>
          <thead id="hx5p7"><dfn id="hx5p7"><output id="hx5p7"></output></dfn></thead>

          <form id="hx5p7"><listing id="hx5p7"></listing></form>
            <thead id="hx5p7"><var id="hx5p7"><output id="hx5p7"></output></var></thead>

            <address id="hx5p7"><listing id="hx5p7"><ins id="hx5p7"></ins></listing></address>
            <address id="hx5p7"><dfn id="hx5p7"></dfn></address>

              <address id="hx5p7"></address>

                <sub id="hx5p7"><var id="hx5p7"><ins id="hx5p7"></ins></var></sub>
                <address id="hx5p7"><var id="hx5p7"></var></address><address id="hx5p7"></address>

                <sub id="hx5p7"><dfn id="hx5p7"><output id="hx5p7"></output></dfn></sub>

                <sub id="hx5p7"></sub>

                <sub id="hx5p7"><listing id="hx5p7"><ins id="hx5p7"></ins></listing></sub>

                    <address id="hx5p7"></address>
                  <sub id="hx5p7"></sub>